This is what you want> https://www.michiganavionics.com/produc ... i-gateway/
Works fine integrating a uAvionix Ping ADS-B IN receiver or similar (eg SkyEcho) into the iEFIS.
Search found 68 matches
- Thu Apr 25, 2024 3:31 am
- Forum: EFIS Systems
- Topic: ADSB-in and out with a Voyager Odyssey G2
- Replies: 7
- Views: 226
- Mon Apr 22, 2024 6:23 pm
- Forum: EFIS Systems
- Topic: mgl discovery lite and rdac xf
- Replies: 8
- Views: 292
Re: mgl discovery lite and rdac xf
They should be 120 ohms, not Kohms.Rocknrollrefugee wrote: ↑Mon Apr 22, 2024 10:29 am i have rwo resistors , one at each end in the 9 pin d sub the ar 12 kohms
- Thu Mar 28, 2024 5:35 pm
- Forum: EFIS Systems
- Topic: oil pressure
- Replies: 2
- Views: 204
Re: oil pressure
Pull-up resistor switched ON?
Should be OFF.
Should be OFF.
- Wed Feb 07, 2024 6:04 pm
- Forum: EFIS Systems
- Topic: Fuel pressure
- Replies: 1
- Views: 310
Re: Fuel pressure
Re your fuel pressure- make sure you have the fuel pressure pull-up and pull-down switches set correctly for your fuel sensor.
Older automotive 'can' style resistive sensors- PU ON, PD OFF.
Newer 912 4-20mA style sensors- PU OFF, PD ON.
UMA style 0-5V active sensors- PU OFF, PD OFF.
Older automotive 'can' style resistive sensors- PU ON, PD OFF.
Newer 912 4-20mA style sensors- PU OFF, PD ON.
UMA style 0-5V active sensors- PU OFF, PD OFF.
- Mon Jan 29, 2024 7:22 pm
- Forum: EFIS Systems
- Topic: IEFIS Simulatior
- Replies: 6
- Views: 1081
Re: IEFIS Simulatior
it is not very clear to me where are stored the screens that you are working on, when you close the desing file a different screen is shown on the page that you are editing. Re files, simplest is to either use the SIM file manager to transfer files to the SD card, or us the script library generator...
- Mon Jan 29, 2024 6:04 pm
- Forum: EFIS Systems
- Topic: IEFIS Simulatior
- Replies: 6
- Views: 1081
Re: IEFIS Simulatior
The designed/simuator RDAC fuel level sliders don't work, but the fuel level system works fine on real hardware.
Just go for it, set up the level calibration in real life- it all works!
Just go for it, set up the level calibration in real life- it all works!
- Fri Dec 08, 2023 5:18 pm
- Forum: MGL Radio frequency products
- Topic: V6 settings for single seat homebuilt aircraft
- Replies: 1
- Views: 4812
Re: V6 settings for single seat homebuilt aircraft
Simplest is to set the VOX at its upper limit- that way it will never open the intercom channel and your headset will remain quiet except when transmitting or receiving. When you press PTT the mic is always live, so the VOX setting does not affect transmission. Set your squelch and volume as require...
- Fri Dec 01, 2023 7:10 pm
- Forum: The MGL/Infinitec Singles
- Topic: BLAZE EMS-2 & RDAC FL1 vs AUX2
- Replies: 3
- Views: 3706
Re: BLAZE EMS-2 & RDAC FL1 vs AUX2
Select RDAC as the source for that channel- that way it will pick up the RDAC FL input.
The bits in the manual re analog channel setups mainly relate to using the direct analog inputs on the EMS2.
The bits in the manual re analog channel setups mainly relate to using the direct analog inputs on the EMS2.
- Fri Dec 01, 2023 5:26 pm
- Forum: The MGL/Infinitec Singles
- Topic: BLAZE EMS-2 & RDAC FL1 vs AUX2
- Replies: 3
- Views: 3706
Re: BLAZE EMS-2 & RDAC FL1 vs AUX2
Best to use FL1- that is its intended use.
Routing, signal conditioning, tank linearisation and display are all available to you by default using that input.
Routing, signal conditioning, tank linearisation and display are all available to you by default using that input.
- Mon Oct 30, 2023 12:25 am
- Forum: EFIS Systems
- Topic: Fuel level sender for MGL Extreme EMS and RADAC-MAP
- Replies: 6
- Views: 18308
Re: Fuel level sender for MGL Extreme EMS and RADAC-MAP
So my understanding is that the MGL Extreme EMS will accept a signal from the fuel level sender either as ohms or as voltage depending on the RADAC switch setting. I'm debating using one of the cheaper float types versus the capacitance type MGL has on their website (which costs 10 times more) if I...